Dyna-Glo Kerosene Heater Replacement Wicks | Official Parts
Our genuine replacement wicks restore your Dyna-Glo kerosene heater to factory performance. Each wick is manufactured to exact OEM specifications, using tightly woven fiberglass that resists degradation from heat and fuel exposure.
A worn wick reduces heat output, increases soot production, and creates uneven flames that waste fuel. We designed these replacement wicks to deliver the same clean burn and consistent heat distribution you experienced when your heater was new. Compatible with most Dyna-Glo convection and radiant kerosene models, each wick ships with installation instructions and fits securely into your heater's wick assembly without modification.
- OEM-grade fiberglass construction resists fraying and fuel breakdown
- Pre-sized height matches factory wick dimensions for proper flame control
- Compatible with Dyna-Glo RMC-55R7, WK11C8, and RMC-95C6 series heaters
- Maximum burn surface ensures efficient fuel vaporization
- Includes detailed replacement instructions and compatibility chart
Wick Material & Construction
Our replacement wicks use a tightly woven fiberglass weave that outperforms generic cotton alternatives. Fiberglass fibers maintain structural integrity at the high temperatures found in kerosene combustion chambers, while cotton wicks char and compress after a few dozen burn cycles.
The weave density controls capillary action — how quickly kerosene travels from the fuel reservoir to the flame surface. Too loose, and you get fuel dripping and flare-ups. Too tight, and the flame starves, producing carbon monoxide and soot. We calibrate every wick to match the exact capillary rate Dyna-Glo engineers specified for your heater model.
Compatible Heater Models
This replacement wick fits Dyna-Glo convection kerosene heaters in the RMC-55R7, WK11C8, RMC-95C6, and RMC-LPC80 series. It also works with the DGH-series portable heaters rated between 10,000 and 23,000 BTU.
Before ordering, locate your model number on the heater’s data plate — usually found on the rear panel or fuel tank collar. Cross-reference that model number with the compatibility chart included in every wick package. If your heater uses a circular wick holder, this replacement will fit. Rectangular wick assemblies require a different part.
When to Replace Your Wick
Replace your Dyna-Glo kerosene heater wick when you notice reduced heat output, excessive soot on walls or ceilings, or difficulty adjusting flame height. A wick nearing end-of-life produces an uneven flame with blue and yellow sections instead of a uniform orange glow.
Most wicks deliver 500 to 1,000 burn hours depending on fuel quality and operating conditions. If you run your heater eight hours daily during a four-month heating season, expect to replace the wick annually. Operating on contaminated kerosene or allowing the fuel tank to run dry accelerates wick degradation.
Complete Your Heater Maintenance Kit
What people are saying
Wick Replacement Questions
Replace your wick when you notice reduced heat output, excessive soot, difficulty adjusting flame height, or uneven burning. Under normal use with clean 1-K kerosene, a quality wick lasts 500 to 1,000 burn hours — typically one to two heating seasons. Heavy use or contaminated fuel shortens wick life. If you run your heater daily throughout winter, plan to replace the wick annually.
This replacement wick fits Dyna-Glo convection models including RMC-55R7, WK11C8, RMC-95C6, RMC-LPC80, and DGH-series portable heaters rated 10,000 to 23,000 BTU. Check your heater's data plate for the model number and cross-reference it with the compatibility chart included with every wick. Circular wick holders use this part; rectangular assemblies require a different replacement.
Yes, soak the new wick in clean 1-K kerosene for 60 minutes before installation. Dry fiberglass cannot wick fuel properly, resulting in weak flames and incomplete combustion. After soaking, install the wick and run the heater outdoors at medium heat for 30 minutes to burn off manufacturing residues. This break-in procedure prevents odors during indoor use and ensures optimal capillary action.
Always use water-clear 1-K kerosene in your Dyna-Glo heater. Red-dyed K-2 kerosene contains higher sulfur levels that accelerate wick degradation and produce more soot. Contaminated fuel clogs the fiberglass weave and reduces burn efficiency. Store kerosene in sealed containers away from sunlight to prevent water contamination and algae growth that damage the wick.
You need a flathead screwdriver, adjustable wrench, and a container to drain fuel from the tank. Most Dyna-Glo heaters also require a Phillips screwdriver to remove cabinet panels. The entire replacement process takes 15 to 20 minutes. Drain the fuel tank completely before starting, and work in a well-ventilated area to avoid fume buildup. Detailed step-by-step instructions ship with every replacement wick.
Soot from a new wick usually indicates incomplete combustion caused by improper flame height, contaminated fuel, or insufficient break-in. Lower the flame slightly and ensure you're burning clean 1-K kerosene. If the wick wasn't pre-soaked for 60 minutes, it may not be wicking fuel evenly. Run the heater outdoors at medium heat for 30 minutes to complete the break-in cycle, then recheck flame quality indoors.
A worn wick shows visible signs including charred or crumbling edges, uneven burn patterns with blue and yellow flame sections instead of uniform orange, reduced heat output even at maximum setting, and excessive black smoke or soot deposits. If adjusting the wick height no longer changes flame intensity smoothly, the fiberglass has lost structural integrity and requires replacement.